Sometimes, it is good to wash clothes, We need not only high quality detergent, but also hot water. Our grandmothers and mothers, wanting to do the laundry perfectly clean, boiled it. Luckily, we are delivered from this long and unpleasant procedure, because all modern washing machines can heat water to a temperature 95 degrees. But just in case, if the device is working properly.
Unfortunately, problems with the hot water in stiralka occur very frequently. The reason for that can be both careless users, and breakage of the internal mechanisms. If there was such a nuisance, do not worry. The first thing to try to understand, what happened.
Selected washing program without heating water
first, What you should do, when it became clear, that the washing machine does not heat the water - it is to verify the selected wash cycle. Not all programs provided heating, many of them are designed for washing at 30-40 degrees. so look, which mode you have selected.
In many devices can manually set the temperature of heating water. But if you have installed, for example 95 degrees, and select a program, wherein heat is provided to 60 degrees, stiralka prefers not hand, and software settings. If there is any doubt, Attributable to the instructions in the machine.
Improper connection stiralki
Sometimes the owners of the washing machine is connected it yourself, not really reading all the subtleties. As a result, the following problem arises - in the process of constantly washing machine drains water down the drain and fill new. Naturally, In such circumstances, it simply does not have time to warm up.
You can check the correct connection and independently. Stiralki drain hose must be above the tank. Normally it is attached to the siphon or sewer pipe at 50-60 cm from the floor. If it is actually below, all typed water goes down the drain by gravity.
If you can not see the place of the hose connection, you can conduct a simple test. Start any program and wait for the wash, until finished machine pour water into the tank. Then stop the cycle and enable water drainage. When she begins to decrease, press "Pause". If the liquid level in the tank remains the same, cause of the problem must be sought elsewhere. If after stopping the draining water continues to go, so, stiralka connected properly. Recommended postpone washing and cause masters, who re-connect device according to the rules.
Faulty heating element or thermostat
Stiralka connected correctly, washing program is selected correctly, a water heating does not occur? The most likely reason - the failure of the heating element (heating element) or damage of the wires, coming to him. It is worth checking the wiring and the first. Carefully inspect them for defects. Sometimes the wires are cut off due to the strong vibrations of the washing machine. Damaged components must be replaced.
To test himself TEN, you'll need a multimeter. If you do not have this device or you do not know how to use it, better to call the master. diagnostic service is not expensive, and some service centers spend her free, if you then they will order repair. So you will make mistakes.
Supply water heating (thermostat), system which delivers a signal, too can fail. In this case, water or overheated, either it remains cold. Because of this failure stiralka can greatly delay the washing process, or vice versa, very fast to finish it.
To check the thermostat operation, it must be removed from the washing machine and measure the resistance of a multimeter. Then place the sensor in the hot water and again make measurements. If the figures differ, accessories straight, if not - you need a replacement.
Fault Management Module
stiralki control module is responsible for all processes, including for water heating. It can fail for various reasons - because of the voltage drop, water splashing, factory defects, contact cliff. As a result, the stabilizer control board does not give TENu team for water heating.
Restore the software module rarely works, and few service centers are taking up this job. Most often in the case of a breakdown the control board must be changed. Unfortunately, alone is almost impossible to do. The replacement cost is quite high, but attempts to save, by working with their hands, very rarely end successfully. Better just to look for a reliable service center.
How to call the master of a house in Vinnitsa?
Choosing a workshop for repair of washing machines, give preference to, who spend all the work at home with customers, not to have to spend more on transportation device. Service center "Vinnitsa-Repair" is such a. Call the master at home you can, leaving the shop online application or contact her via phone.
Any repairs carried out promptly and efficiently. Experts travel to all parts of the city and into the suburbs on the day of filing. Before starting work, be sure the device is held diagnostics to identify the cause of failure. If during the inspection it turns out, stiralka that does not heat the water because of the failure of PETN, it will change to the new. This will set the original part of the desired brand. The new kit is warranted against 3 to 12 months. In the case of repeated failure during this period, you can always refer to the workshop for warranty repairs.
