When broken washing machine, not everyone wants to spend money on a professional master of Service. In this connection there is a reasonable question: Is it possible to repair washing machines with their own hands? Definitely, Yes, but not in all cases. Therefore it is necessary to understand, what exactly is this or that fault, and what caused it. Here we get acquainted with all major malfunctions of washing machines. With this you can understand, Brother Lee for independent repair shop or call the.
we define the problem
Typical damage can be very different, since the mechanism stiralki - not the easiest. This is especially true of modern models, possessing broad functionality. Their design is even more complex and failure often requires professional maintenance. But there is a fault, which are characteristic for almost any model of the washing machine. On them will be discussed below.
Strong vibration during the spin cycle
Often, users are complaining about "jumping" stiralku. Such intense vibration may be caused by improper installation of the device, and malfunctions of individual components. It is also one of the reasons - failure to comply with the rules of operation. If you regularly overload the washing machine drum, the "bumpiness" probably explained by this.
As for the incorrect installation, you must first make sure, that the unit is running on a flat surface. Any defects often provoke noises, including vibration. The machine can make noise due to worn shock absorbers, bearings or springs. Opposed to the failed or weakened his attachment have the same effect.
I stopped spinning drum
It is important to know exactly, when it was overtaken by a fault your washing machine. If the drum is stopped during the spin cycle, check the status of underwear. The problem in the spin cycle, if the clothing is not a soap, but wet. When the drum is jammed "tight" and it can not even crank arms, it speaks about deterioration of bearings or motor belt. Often it gets there and the foreign object, which interferes with the normal functioning of the washing machine. When, when the drum rotates manually, but still it does not work automatically, possibly, the unit needs replacement brushes, belt, motor or electronic control module.
And here we should not forget about the likely reloading tank. The last "smart" model stiralok give appropriate error in the display. If you reduce the amount of clothing, and washing resumes in the correct mode, the failure as such, and there was no.
stiralka flows
Diagnosis will depend on the location, type and amount of leaks. If the puddle formed directly under the unit, then broke down the drain filter, or rather its attachment. This problem can be eliminated with their hands, simply tighten fasteners tighter. Such symptoms are typical for the defective nozzle of the washing machine, to be replaced.
Flow in the dispenser for detergents are the result of two factors: clogging and excessive pressure in the water. Cuvette for the powder is very often contaminated adhering means for washing. It is better not to allow any blockages and regularly wash your washing machine dispenser. A high pressure water is easily adjustable valve.
If you see a leak from the hatch, it has deteriorated rubber sleeve. She could simply wear or has been damaged due to careless handling. Download things stiralki tank as gently as possible: coarse result of friction tires damaged much faster.
It does not heat water
It must be ensured, that you set the correct temperature conditions for the wash, and that the device is connected correctly. In the latter case, the water will continue to be recruited and to merge, so just do not have time to warm up. If you have seen, that all operating conditions are met, probable failure often lies in faulty Tubular heaters (PETN). He comes into disrepair due to voltage fluctuations, violations of the rules of operation of the washing machine and irregular care. TEN must be periodically cleaned of scale, otherwise it tightly cover part, and that burns out due to excessive heat. breakdowns, connected to the control unit, It is also possible.
Call the master or repair yourself?
It all depends on each individual case. Stiralki repairs can be made with their own hands for minor faults, eg, during the flow of the drain filter or a dispenser, vibration due to poorly secured counterweight and so on. And in order to eliminate the remaining damage to the washing machine, you need call the master. After the fix will require special tooling and skills. Neglect service center can only aggravate the situation.
_
