In the transformation from a mere means of transportation in a comfortable means of moving the car has undergone if not a thousand, the hundreds of changes. One of them is the ability to connect to the onboard electric cars common household appliances. 
device, allowing to do so - an inverter. Despite the apparent complexity of the calculations, underpinning the design and production of this device, customers increasingly prefer to install it in your car by yourself. Really, Public theoretical materials, Internet experience of colleagues, known characteristics of the device allow it to do.
How to Install a Car Power Inverter on their own and that this will?
questions, which will try to answer in this article. We begin with the second: при инсталляции прибора своими руками необходимо четко “просчитать” возможную нагрузку, with the result that the car owner clearly understands, What appliances can be connected, and what - no. The second positive effect - small, but tangible savings. And the third - you will always be assured of the quality of the work done by wiring, electrical connections, etc..
Answering the first part of the question, We draw your attention to the fact, what is a given device and the procedure for its installation in the back of car. Before you buy a car inverter and begin installation, It decided to examine its working principle. It's simple: it is enclosed in a small package size converting transformer, Automation and Control device, input and output in the form of rosettes, cable.
Principle of operation - electricity conversion 12 VDC 220 VAC. The main characteristic of the inverter, by which it is selected and compared, - wattage. Her knowledge is a critical parameter, because it means the total power devices, которые можно “запитать” от розетки устройства в 220 AT. If this capacity is exceeded, there is a risk of the car battery explosion, and failure of its generator. Therefore, when the device temperature is exceeded (somewhere in the 60-65 °) triggered automatic cut.
The next phase - installation.
Let's, You Decide, which model to buy. purchased, brought home, We looked at his chart connection Pay attention ..., that the electricity conversion device power up 500 W can be connected to the onboard network via the cigarette lighter socket. devices more 500 W - directly from the battery.
Connect said power consumers above recommended during engine operation, when the generator powers the battery. Otherwise guaranteed rapid discharge of the battery cars, after which it can not even start.
so, We decided to - connect from the battery. Now you need to collect:
- instruments (knife, pliers, the keys);
- materials (wire of adequate gauge, which is determined by the table corresponds to the power, terminals, adhesive tape, Insulating tubes, etc.).
Next - we disconnect the battery from the on-board network (remove all the terminals to the battery terminals). Paving the power wire from the engine compartment into the interior through the technological holes (without the presence of these movable parts). Good reception installation in vehicles with automatic transmission - through hole cover missing clutch pedal. The wire should be securely fastened to either the structural parts of the body, либо надежно “притянут” к пучкам других проводов.
Experienced electricians recommend you to connect the inverter cable to the battery through fuse box. Usually, it has a blank space for additional electrical cars. The appropriate place is established fuse - fuse capacity, slightly less than the inverter capacity. Next - simpler. “Обжимаем” клеммой плюсовую жилу кабеля и подсоединяем её к “+” выводу АКБ. Вторую жилу можно присоединять к точке “массы” авто, which may be downloaded in the engine compartment, and inside the cabin.
Now you must use the self-tapping screws, Brackets or bundles, reliably strengthen the inverter in the cabin. Already standard room for its placement - there, where there is no risk of physical damage, free space for better cooling of its housing. And this is - a torpedo on the passenger side, under the passenger seat, behind the front seats, or in the trunk (important for large models).
The special car (hunting-fishing tourism, for sporting events on the roads and in the mud) Placement may be at least on the ceiling, главное – чтобы к нему был обеспечен быстрый и удобный доступ. После проверки изоляции всех соединений можно подключать к АКБ остальные провода сети и начинать эксплуатацию авто! Based on materials: http://auto.tsn.ua/news/rekomendacii-forter-kak-ustanovit-avtomobilnyy-invertor-602891.html. Узнать больше о инверторах вы можете из видео к этой статье.
